Blog
  2. ASTM
  3. Nuts
  4. ASTM F467/F467M
  5. ASTM F467 UNS N06625 Inconel 625 Nuts

ASTM F467 UNS N06625 Inconel 625 Nuts

Commercial wrought nonferrous Square Nuts & hex Nuts in common use and intended for general service applications

ASTM F467 UNS N06625 Inconel 625 Nuts Hex Nut, Heavy hex Nut, Square Nuts, Hexagon High Nuts, Slotted Nuts

ASTM F467 UNS N06625 Inconel 625 Nuts specification covers the requirements for commercial wrought nonferrous nuts 1/4 inch to 1 1/2 inch in imperial sizes and M6 to M36 inclusive in diameter in a number of alloys in common use and intended for general service applications. Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification ASTM F468.

Related Specifications of ASTM F467 UNS N06625 Inconel 625 Nuts Bolting

F468 B564 F2882 F3042

ASTM F467 N06625 Alloy 625 Inconel 625 Nuts Chemical Composition

ASTM F467/467M N06625 Alloy 625 Inconel 625 Nickel and Nickel-Base Alloys

UNS Designation Number Alloy General Name Al C, max Cr Cu A Fe, max Mn, max Ni A P, max Si, max Ti Co, max Mo S, max V W Cb †
ASTM F467/F467M Grade N06625 625C Ni-Cr-Mo-Cb 0.40 max 0.10 20.0- 23.0 . . . 5.0 max 0.50 58.0 min 0.015 0.50 max 0.40 max 1.00 max 8.0- 10.0 0.015 . . . . . . 3.2- 4.2
(A) Elements shown as balance shall be arithmetically computed by deducting the sum of the other named elements from 100. (B) Cobalt is to be counted as nickel. (C) Alloy 625 material shall be refined using the electroslag remelting process (ESR), or the vacuum arc remelting process (VAR).

ASTM F467 N06625 Alloy 625 Inconel 625 Nuts Mechanical Requirements

ASTM F467 Mechanical Requirements (Inch)

Alloy Mechanical Property Marking Hardness, min A Proof Stress, Hex Nut min, ksi Proof Stress, Heavy Hex Nut min, ksi B
  • (A) For aluminum and titanium alloys hardness values are for information only.
  • (B) Proof stress values for heavy hex nuts are based on 1.08 times the value for corresponding regular hex nuts.
  • (C) Aluminum alloy 2024-T4 shall be supplied in naturally aged condition. This material is not recommended for nuts in sizes greater than 1/4 (0.250) in.

ASTM F467M Mechanical Requirements (Metric)

Alloy Mechanical Property Marking Hardness, min A Proof Stress, Mpa
ASTM F467M Ni 625 F 467AC 85 HRB-35 HRC 415
  • (A) For aluminum and titanium alloys hardness values are for information only.
  • (B) Aluminum alloy 2024-T4 shall be supplied in naturally aged condition. This material is not recommended for nuts in nominal thread diameter larger than M6.

ASTM F467 UNS N06625 Inconel 625 Nuts Tensile Stress Areas and Threads per Inch

Nominal Size, in. Coarse Threads-UNC Fine Threads-UNF 8 Thread Series-8UN
Threads/in. Stress Area A , in 2 Threads/in. Stress Area A , in 2 Threads/in. Stress Area A , in 2
1 / 4 20 0.0318 28 0.0364 . . . . . .
5 / 16 18 0.0524 24 0.0580 . . . . . .
3 / 8 16 0.0775 24 0.0878 . . . . . .
7 / 16 14 0.1063 20 0.1187 . . . . . .
1 / 2 13 0.1419 20 0.1599 . . . . . .
9 / 16 12 0.1820 18 0.2030 . . . . . .
5 / 8 11 0.2260 18 0.2560 . . . . . .
3 / 4 10 0.3340 16 0.3730 . . . . . .
7 / 8 9 0.4620 14 0.5090 . . . . . .
1 8 0.6060 12 0.6630 . . . . . .
1 1 / 8 7 0.7630 12 0.8560 8 0.790
1 1 / 4 7 0.9690 12 1.0730 8 1.000
1 3 / 8 6 1.1550 12 1.3150 8 1.233
1 1 / 2 6 1.4050 12 1.5810 8 1.492
  • (A) Tensile stress areas are computed using the following formula:
  • A s = 0.7854 [ D - 0.9743/n ]
    • where:
    • As = tensile stress area, in. 2 ,
    • D = nominal size (basic major diameter), in., and
    • n = number of threads per inch.

ASTM F467 UNS N06625 Inconel 625 Nuts Tensile Stress Areas and Threads per Metric

Nominal Nut Diameter and Thread Pitch Stress Area, A mm 2 Nominal Nut Diameter and Thread Pitch Stress Area, A mm 2
M6 × 1 20.1 M16 × 2 157
M8 × 1.25 36.6 M20 × 2.5 245
M10 × 1.5 58.0 M24 × 3 353
M12 × 1.75 84.3 M30 × 3.5 561
M14 × 2 115 M36 × 4 817
  • (A) Tensile stress areas are computed using the following formula:
  • As = 0.7854 (D − 0.9382P) 2
    • where:
    • As = tensile stress area, mm. 2 ,
    • D = nominal size (basic major diameter), mm., and
    • n = number of threads per mm.

ASTM F467 UNS N06625 Inconel 625 Nuts Heat Treatment

Alloy Condition
Copper (all alloys) As formed or stress relieved at manufacturer's option
Nickel alloys 400 and 405 As formed or stress relieved at manufacturer's option
Nickel alloy 500 Solution annealed and aged
Aluminum alloy 2024-T4 Solution treated and naturally aged
Aluminum alloy 6061-T6 Solution treated and artificially aged
Aluminum alloy 6262-T9 Solution treated, artificially aged, and cold worked
Titanium 625 Annealed

ASTM F467 UNS N06625 Inconel 625 Nuts Bolting Surface Treatment Specifications

ASTM F467 UNS N06625 Inconel 625 Nuts Bolting Components Marking

Product Shall be Marked with our manufacturing trade mark "TorqBolt" or "TB" along with the designated Grade.
Grade and manufacturer’s identification symbols shall be applied to one end of studs and to the heads of bolts and screws of all sizes. (If the available area is inadequate, the grade symbol may be marked on one end and the manufacturer’s identification symbol marked on the other end.) For bolts and screws smaller than 1⁄4 in. [6 mm] in diameter and studs smaller than 3⁄8 in. [10 mm] in diameter and for 1⁄4 in. [6 mm] in diameter studs requiring more than a total of three symbols, the marking shall be a matter of agreement between the purchaser and the manufacturer.

ASME Dimensional Standards

B18.2.2 Imperial Square, Hex, Heavy Hex, Lock, Heavy Hex Lock Nuts
B18.2.4.1M Metric Hex Nuts
B18.2.4.6M Metric Heavy Hex Nuts
ISO 4033 Hexagon High Nuts
ISO 4032 Hexagon Nuts
ISO 4035 Hexagon Lock Nuts

ASTM F467 UNS N06625 Inconel 625 Nuts N06625 Alloy 625 Inconel 625 Nuts Bolting Certifications

  • EN 10204 3.1
  • EN 10204 3.2
  • PED 2014/68/EC
  • MERKBLATT AD 2000 W2/W7/W10
  • API 20 E BSL 1/ BSL 2
  • NACE MR 0175
  • NACE MR 0103

ASTM F467 UNS N06625 Inconel 625 Nuts N06625 Alloy 625 Inconel 625 Nuts Testing Standards

E18 Test Methods for Rockwell Hardness of Metallic Materials
E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials
E709 Guide for Magnetic Particle Testing
A962/A962M Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
A788/A788M Specification for Steel Forgings, General Requirements

ASME Threading Specifications

ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
ASME B1.3 Screw Thread Gaging System for Dimensional Acceptability - Inch Screw Threads (IN, UNR, and UNJ)
ASME B1.13M Metric Screw Threads - M Profile
ASME B1.21M Metric Screw Threads - MJ Profile
ASME B1.2 Gauges & gauging for Unified Screw Threads(Imperial)

ASTM F467 UNS N06625 Inconel 625 Nuts Supplementary Requirements

S1 Stress Corrosion Requirements, Copper Alloys
S2 Shipment Lot Testing
S3 Dye Penetrant Inspection
S4 Heat Control (Alloys 400, 405, and 500 Only)