EN Standards

STANDARDSDESCRIPTION
EN ISO 15330-1999 Fasteners – Preloading test for the detection of hydrogen embrittlement – Parallel bearing surface method {ISO 15330:1999}
EN ISO 3269-2000 Fasteners – Acceptance inspection {ISO 3269:2000}
EN 493-1992 Fasteners; Surface discontinuities; Nuts
EN ISO 4042-1999 Fasteners – Electroplated coatings {ISO 4042:1999}
EN 792-6-2000 Hand-held non-electric power tools – Safety requirements – Part 6: Assembly power tools for threaded fasteners
EN 1075-1999 Timber structures – Test methods – Joints made with punched metal plate fasteners
EN ISO 4759-1-2000 Tolerances for fasteners – Part 1: Bolts, screws, studs and nuts; product grades A, B and C {ISO 4759-1:2000}
EN ISO 10964-1997 Adhesives – Determination of torque strength of anaerobic adhesives on threaded fasteners {ISO 10964:1993}
EN 12242-1999 Touch and close fasteners – Determination of peel strength
EN 409-1993 Timber structures – Test methods – Determination of the yield moment of dowel type fasteners – Nails
EN ISO 16048-2003 Passivation of corrosion-resistant stainless steel fasteners {ISO 16048:2003}
EN 792-14-1995 Hand-held non electric power tools – Safety requirements – Part 14: Assembly power tools for non-threaded mechanical fasteners
EN 20898-2-1993 Mechanical properties of fasteners; Part 2: Nuts with specified proof load values; Coarse thread {ISO 898-2:1992}
EN 26891-1991 Timber structures – Joints made with mechanical fasteners – General principles for the determination of strength and deformation characteristics {ISO 6891:1983}
EN ISO 12777-1-1996 Methods of test for pallet joints – Part 1: Determination of bending resistance of pallet nails, other dowel-type fasteners and staples {ISO 12777-1:1994}
EN ISO 3506-2-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 2: Nuts {ISO 3506-2:1997}
EN 26157-3-1991 Fasteners; surface discontinuities; part 3: bolts, srews and studs for special requirements {ISO 6157-3:1988}
EN ISO 16426-2002 Fasteners – Quality assurance system {ISO 16426:2002}
EN 12240-1997 Touch and close fasteners – Determination of the overall and effective widths of tapes and the effective width of a closure
EN ISO 3506-4-2003 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 4: Tapping screws {ISO 3506-4:2003}
EN 4603-1999 Aerospace series – Molybdenum disulphide coatings of fasteners – Technical specification
EN ISO 4753-1999 Fasteners – Ends of parts with external ISO metric screw thread {ISO 4753:1999}
EN 28839-1991 Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals {ISO 8839:1986}
EN 1382-1999 Timber structures – Test methods – Withdrawal capacity of timber fasteners
EN 20898-7-1995 Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm {ISO 898-7:1992}
EN 28970-1991 Aerospace series – Screws, 100?countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 12549-1999 Acoustics – Noise test code for fastener driving tools – Engineering method
EN 912-1999+AC-2000 Timber fasteners – Specifications for connectors for timber
EN 792-13-2000 Aerospace series – Nuts, elliptical clinch, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?
EN ISO 4759-3-2000 Tolerances for fasteners – Part 3: Plain washers for bolts, screws and nuts – Product grades A and C {ISO 4759-3:2000}
EN 2959-1999 Aerospace series – Heat resisting alloy NI-PH1302 {NiCr20Co13Mo4Ti3Al} – Solution treated and cold worked – Bar for forged fasteners 3 mm D 30 mm
EN 1660-1994 Mechanical fasteners – Hexagon products – Widths across flats
EN 13780-2003 Touch and close fasteners – Determination of longitudinal shear strength
EN 383-1993 Timber structures – Test methods – Determination of embedding strength and foundation values for dowel type fasteners
EN 2098-6-1981 GOOGLEaLL1
EN 1383-1999 Timber structures – Test methods – Pull through resistance of timber fasteners
EN ISO 10683-2000 Fasteners – Non-electrolytically applied zinc flake coatings {ISO 10683:2000}
EN 20225-1991 Fasteners; Bolts, screws, studs and nuts; Symbols and designation of dimensions {ISO 225:1983}
EN ISO 3506-3-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 3: Set screws and similar fasteners not under tensile stress {ISO 3506-3:1997}
EN 12241-1999 Touch and close fasteners – Method for closure prior to washing and drying or dry cleaning
EN ISO 898-6-1995 Mechanical properties of fasteners – Part 6: Nuts with specified proof load values – Fine pitch thread {ISO 898-6:1994}
EN ISO 3506-1-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 1: Bolts, screws and studs {ISO 3506-1:1997}
EN 12243-1999 Touch and close fasteners – Determination of dimensional change in washing and drying and dry cleaning
EN 1059-1999 Timber structures – Product requirements for prefabricated trusses using punched metal plate fasteners
EN ISO 898-1-1999 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs {ISO 898-1:1999}
EN 12512-2001 Timber structures – Test methods – Cyclic testing of joints made with mechanical fasteners
EN 20273-1991 Fasteners; Clearance holes for bolts and screws {ISO 273:1979}
EN 792-1-2000 Hand-held non-electric power tools – Safety requirements – Part 1: Assembly power tools for non-threaded mechanical fasteners
EN ISO 898-5-1998 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners not under tensile stresses {ISO 898-5:1998}
EN ISO 5845-1-1999 Technical drawings – Simplified representation of the assembly of parts with fasteners – Part 1: General principles {ISO 5845-1:1995}
EN 10269-1999 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 26157-1-1991 Fasteners; surface discontinuities; Part 1: Bolts, srews and studs for general requirements {ISO 6157-1:1988}
STANDARDSDESCRIPTION
EN 2889-1999 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN 2888-1995 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short threaded, in corrosion resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/425?
EN 2936-1996 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy}, silver plated – Classification: 1210 MPa {at ambient temperature}/730?
EN ISO 10664-1999 Hexalobular internal driving feature for bolts and screws {ISO 10664:1999}
EN 3724-2003 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in titanium alloy TI-P64001, MoS2 coated – Classification: 1 100 MPa {at ambient temperature} / Note: To be replaced by EN 3724 {2003-05}.
EN 24015-1991 Hexagon head bolts; Product grade B; Reduced shank {shank diameter = pitch diameter} {ISO 4015:1979}
EN 2931-1994 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286} – Classification: 900 MPa {at ambient temperature}/650 ?
EN 3379-1996 Aerospace series – Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy}, for increased height nuts – Classification: 1210 MPa {at ambient temperature}/730?
EN 2935-1996 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa {at ambient temperature}/730?
EN 2925-1994 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286} – Classification: 900 MPa {at ambient temperature}/650?
EN 4071-1999 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated – Classification: 1100 MPa {at ambient temperature}/425?
EN 4402-1999 Aerospace series – Lockbolts, 100?countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001, with aluminium pigmented coating, metric series – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 13918-1998 Welding – Studs and ceramic ferrules for arc stud welding {ISO 13918:1998}
EN 1450-1996+A1-1998 Plastics piping systems – Glass-reinforced thermosetting plastics {GRP} components – Test methods to prove the design of bolted flange joints
EN 3757-1998 Aerospace series – Nuts, anchor, self-locking, floating, self-aligning, two lug, in heat resisting steel, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/315?
EN 4009-2003 Aerospace series – Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718} – Classification: 1550 MPa {at ambient temperature}/650? / Note: To be replaced by EN 4009 {2003-0
EN 6110-2000 Aerospace series – Bolts, blind, 100?flush head, stainless steel
EN 4458-2000 Aerospace series – Studs, MJ threads, in titanium alloy TI-P64001, MoS2 coated, with serrated locking ring in corrosion resisting steel – Strength class: 1100 MPa {at ambient temperature}; Technical specification
EN 14399-4-2002 High-strength structural bolting for preloading – Part 4: System HV; Hexagon bolt and nut assemblies
EN ISO 10434-2002 Bolted bonnet steel gate valves for petroleum and natural gas industries {ISO/DIS 10434:2002}
EN 4421-2000 Aerospace series – Studs, in titanum alloy TI-P64001, MoS2 coated, with serrated locking ring, in corrosion resisting steel – Strength class: 1100 MPa {at ambient temperature}
EN 2859-1995 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
EN 1515-1-1999 Flanges and their joints – Bolting – Part 1: Selection of bolting
EN 3820-1999 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 2549-1995 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 2549-1999 Aerospace series – Screws, 100?countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 4495-1999 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 9974-2-2000 Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing – Part 2: Stud ends with elastomeric sealing {type E} {ISO 9974-2:1996}
EN ISO 4016-2000 Aerospace series – Nuts, elliptical clinch, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?
EN 3907-2003 Aerospace series – Bolts, double hexagon head, normal shank, long thread, in titanium alloy TI-P64001, MoS2 coated – Classification: 1 100 MPa {at ambient temperature}/350? / Note: To be replaced by EN 3907 {2003-05}.
EN 4128-1999 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in heat resisting nickel base alloy, aluminium IVD coated – Classification: 1250 MPa {at ambient temperature}/425?
EN 4312-1999 Aerospace series – Studs, coarse tolerance reduced shank, medium length threads, in heat and corrosion resisting steel, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 2933-1996 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718} – Classification: 1275 MPa {at ambient temperature}/650 ?
EN 20273-1991 Fasteners; Clearance holes for bolts and screws {ISO 273:1979}
EN 2583-1997 GOOGLEaLL1
EN 3832-2003 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718} – Classification: 1550 MPa {at ambient temperature}/650? / Note: To be replaced by EN 3832 {2003-05}.
EN 3833-2003 Aerospace series – Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 {Inconel 718} – Classification: 1550 MPa {at ambient temperature}/650?; Technical specification / Note: To be replaced by EN 3833 {2003-05}.
EN 3011-1998 Aerospace series – Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy}, silver plated – Classification: 1210 MPa {at ambient temperature}/730?
EN 3740-1996 Aerospace series – Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 3052-1999 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/425?
EN ISO 9974-1-2000 Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing – Part 1: Threaded ports {ISO 9974-1:1996}
EN 3112-1995 Aerospace series – Bolts, normal hexagonal head, threaded to head, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN 4321-2003 Aerospace series – Bolts, double hexagon head with lockwire holes, relieved shank, long thread, in heat resisting nickelbase alloy NI-PH2601 {Inconel 718}, silver plated – Classification: 1550 MPa {at ambient temperature}/650? / Note: To be replaced by
EN 28839-1991 Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals {ISO 8839:1986}
EN 14420-3-2002 Hose fittings with clamp units – Part 3: Clamp units, pinned or bolted
EN 26157-3-1991 Fasteners; surface discontinuities; part 3: bolts, srews and studs for special requirements {ISO 6157-3:1988}
EN 4460-2000 Aerospace series – Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel – Installation and removal procedure
EN 3063-1994 Aerospace series – Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa {at ambient temperature}/730?
EN 4172-1999 Aerospace series – Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series – Classification: 1100 MPa {at ambient temperature}/315?
EN 14399-2-2002 High-strength structural bolting for preloading – Part 2: Suitability test for preloading
EN 2932-1996 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 900 MPa {at ambient temperature}/650 ?
EN 10108-2000 Round steel rod for cold formed nuts and bolts – Dimensions and tolerances
EN ISO 898-1-1999 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs {ISO 898-1:1999}
EN ISO 9974-3-2000 Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing – Part 3: Stud ends with metal-to-metal sealing {type B} {ISO 9974-3:1996}
EN 3010-1998 Aerospace series – Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa {at ambient temperature}/730?
EN 3725-2003 Aerospace series – Bolts, pan head, six lobe recess, normal shank, long thread, in titanium alloy TI-P64001, MoS2 coated – Classification: 1 100 MPa {at ambient temparature} / Note: To be replaced by EN 3725 {2003-05}.
EN 14399-1-2002 High-strength structural bolting for preloading – Part 1: General requirements
EN 784-1995 Plain washers for high-strength structural bolting, hardened and tempered
EN 2888-1999 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in corrosion resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/425?
EN 2889-1995 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short threaded, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235 ?
EN 13411-5-2003 Terminations for steel wire ropes – Safety – Part 5: U-bolt wire rope grips
EN ISO 3506-1-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 1: Bolts, screws and studs {ISO 3506-1:1997}
EN ISO 14555-1998 Welding – Arc stud welding of metallic materials {ISO 14555:1998}
EN 4173-1999 Aerospace series – Lockbolts, 100?countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series – Classification: 1100 MPa {at ambient temperature}/315?
EN 3008-1998 Aerospace series – Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718} – Classification: 1275 MPa {at ambient temperature}/650?
EN 2874-1996+AC-1996 Aerospace series – Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated – Classification: 1550 MPa {at ambient temperature}/315?
EN 4322-2003 Aerospace series – Bolts, double hexagon head with lockwire holes, relieved shank, long thread, in titanium alloy TI-P64001, anodized, MoS2 coated – Strength class: 100 MPa {at ambient temperature} / Note: To be replaced by EN 4322 {2003-05}.
EN 781-1992 Hexagon bolts for high-strength structural bolting with large width across flats {thread lengths according to ISO 888}; product grade C; property classes 8.8 and 10.9
EN 3818-2003 Aerospace series – Bolts with MJ threads, in titanium alloy TI-P64001 – Classification: 1 100 MPa {at ambient temperature}; Technical specification / Note: To be replaced by EN 3818 {2003-05}.
EN 1515-2-2001 Flanges and their joints – Bolting – Part 2: Classification of bolt materials for steel flanges, PN designated
EN ISO 4759-1-2000 Tolerances for fasteners – Part 1: Bolts, screws, studs and nuts; product grades A, B and C {ISO 4759-1:2000}
EN 783-1992 Hexagon nuts for structural bolting with large width across flats, style 1; product grade B; property class 10
EN ISO 887-2000 Plain washers for metric bolts, screws and nuts for general purposes – General plan {ISO 887:2000}
EN ISO 8765-2000 Hexagon head bolts with metric fine pitch thread – Product grades A and B {ISO 8765:1999}
EN 3052-1993 Aerospace series; bolts, normal hexagonal head, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated; classification: 1100 MPa {at ambient temperature}/425? {includes amendment A1:1993}
EN 782-1992 Hexagon bolts for high-strength structural bolting with large width across flats {short thread length}; product grade C; property class 10.9
EN 20898-7-1995 Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm {ISO 898-7:1992}
EN 2887-1995 Aerospace series – Bolts, normal hexagonal head, threaded to head, in corrosion resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/425 ?
EN 785-1995 Plain washers, chamfered, hardened and tempered for high-strength structural bolting
EN 4352-2003 Aerospace series – Bolts, double hexagon head with lockwire holes, relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 {Inconel 718}, MoS2 coated – Classification: 1550 MPa {at ambient temperature}/425? / Note: To be rep
EN 2357-1988 Aerospace series – Stud-ends in corrosion resisting steel swaged on type, control cable – Dimensions and loads
EN ISO 4759-3-2000 Tolerances for fasteners – Part 3: Plain washers for bolts, screws and nuts – Product grades A and C {ISO 4759-3:2000}
EN ISO 4014-2000 Hexagon head bolts – Product grades A and B {ISO 4014:1999}
EN 2934-1996 Aerospace series – Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718}, silver plated – Classification: 1275 MPa {at ambient temperature}/650 ?
EN 4459-2000 Aerospace series – Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel – Design standard
EN 4401-1999 Aerospace series – Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, with aluminium pigmented coating, metric series – Classification: 1100 MPa {at ambient temperature}/315?
EN 4498-1999 Aerospace series – Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated, with aluminium pigmented coating – Classification: 1550 MPa {at ambient temperature}/315?
EN 3006-1994 Aerospace series – Bolts, hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286} – Classification: 900 MPa {at ambient temperature}/650?
EN 4501-1999 Aerospace series – Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 20225-1991 Fasteners; Bolts, screws, studs and nuts; Symbols and designation of dimensions {ISO 225:1983}
EN 2859-1999 Aerospace series – Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
EN 780-1992 Hexagon nuts for high-strength structural bolting with large width across flats; product grade B; property classes 8 and 10
EN 4506-1999 Aerospace series – Determination of coefficients of friction of bolts and nuts under specified conditions
EN 26157-1-1991 Fasteners; surface discontinuities; Part 1: Bolts, srews and studs for general requirements {ISO 6157-1:1988}
EN 1665-1997+AC-1998 Hexagon bolts with flange – Heavy series
EN 3202-1995 Aerospace series – Holes and traps for T-head bolts – Design standard
EN 4127-1999 Aerospace series – Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in titanium alloy, aluminium IVDcoated – Classification: 1100 MPa {at ambient temperature}/425?
EN 4407-1997 Aerospace series – Bolts, normal hexagonal head, threaded to head, in titanium alloy, aluminium IVD coated – Classification: 1100 MPa {at ambient temperature}/425?
EN 14399-3-2002 High-strength structural bolting for preloading – Part 3: System HR; Hexagon bolt and nut assemblies
EN 4176-1999 Aerospace series – Lockbolts, 100?countersunk normal head or protruding head, tension-sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating – Collars in titanium TI-P99002 or aluminium alloy 2024 – Metric
EN 2870-1996+AC-1996 Aerospace series – Bolts, normal bihexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 2413-1995 Aerospace series – Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
STANDARDSDESCRIPTION
EN 4069-1996 Aerospace series – Nuts, hexagon, plain, reduced height, reduced across flats, in heat resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/650?
EN ISO 10511-1997 Prevailing torque type hexagon thin nuts {with non-metallic insert} {ISO 10511:1997}
EN 2647-1997 Aerospace series – Nuts, hexagonal, self-locking, ball seat, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN 4447-2000 Aerospace series – Nuts, elliptical clinch, self-locking, UNJ threads, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?
EN 3728-1999 Aerospace series – Shaft-nuts, self-locking, left-hand thread, in heat resisting steel FE-PA92HT {A286}, silver plated
EN ISO 21670-2003 Hexagon weld nuts with flange {ISO 21670:2003}
EN 20898-2-1993 Mechanical properties of fasteners; Part 2: Nuts with specified proof load values; Coarse thread {ISO 898-2:1992}
EN 3726-2003 Aerospace series – Nuts, self-locking, clip, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425? / Note: To be replaced by EN 3726 {2003-05}.
EN 2908-1994 Aerospace series – Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT {A286} – Classification: 1100 MPa {at ambient temperature}/650?
EN ISO 2320-1997 Prevailing torque type steel hexagon nuts – Mechanical and performance requirements {ISO 2320:1997}
EN 3843-1999 Aerospace series – Nuts, bihexagonal, self-locking, with counterbore, in heat resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/650?
EN 3856-2002 Aerospace series – Pipe couplings, 60? spherical, in titanium alloy TI-P64001 – Swivel nuts for thrust wire
EN 3014-2001 Aerospace series – Shank nuts, self-locking, serrated, in heat resisting steel FE-PA2601 {A286} – Classification: 1100 MPa {at ambient temperature}/650?
EN 4591-2000 Aerospace series – Nuts, barrel, self-locking, floating, self-aligning, in heat resisting nickel base alloy, MoS2 lubricated – Classification: 1550 MPa {at ambient temperature}/315?
EN 3149-1996 Aerospace series – Shank nuts – Installation holes, 60°swage, flanges – Design standard
EN ISO 7042-1997 Prevailing torque type all-metal hexagon nuts – Property classes 5, 8, 10 and 12 {ISO 7042:1997}
EN 2415-1982 Aerospace series; nuts, hexagon, slotted/castellated, thin, in steel, cadmium plated; classification 900 MPa/235?
EN 4116-2003 Aerospace series – Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated on thread – Classification: 1100 MPa {at ambient temperature}/425? / Note: To be replaced by EN 4116 {2003-05}.
EN ISO 10512-1997 Prevailing torque type hexagon nuts {with non-metallic insert}, style 1, with metric fine pitch thread – Property classes 6, 8 and 10 {ISO 10512:1997}
EN 1664-1997 Prevailing torque type all-metal hexagon nuts with flange {ISO 7044:1997, modified}
EN 2264-1996 Aerospace series – Nuts, anchor, self-locking, floating, two lug, incremental counterbore, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235 ?
EN ISO 8673-2000 Hexagon nuts, style 1, with metric fine pitch thread – Product grades A and B {ISO 8673:1999}
EN ISO 8662-7-1997 Hand-held portable power tools – Measurement of vibrations at the handle – Part 7: Wrenches, screwdrivers and nut runners with impact, impulse or ratchet action {ISO 8662-7:1997}
EN ISO 898-6-1995 Mechanical properties of fasteners – Part 6: Nuts with specified proof load values – Fine pitch thread {ISO 898-6:1994}
EN 4118-2003 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated on thread – Classification: 1100 MPa {at ambient temperature}/650? / Note: To be replaced by EN 4118 {2003-05}.
EN 3013-1995 Aerospace series – Screws, 100?countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 3752-2003 Aerospace series – Nuts, self-locking, MJ threads, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425?; Technical specification / Note: To be replaced by EN 3752 {2003-05}.
EN 2878-1998 Aerospace series – Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN 4443-2000 Aerospace series – Nuts, elliptical clinch, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?
EN 2997-6-1997 Aerospace series – Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 175? continuous, 200? continuous, 260? peak – Part 6: Hermetic jam-nut mounted receptacle – Product standard
EN 3015-2001 Aerospace series – Shank nuts, self-locking, serrated, in heat resisting steel FE-PA2601 {A286}, silver plated – Classification: 1100 MPa {at ambient temperature}/650?
EN 3196-1994 Aerospace series – Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 1100 MPa {at ambient temperature}/425?
EN 3080-2000 Aerospace series – Pipe coupling 8?0 in titanium alloy – Tees, reduced branch with trust wire nut
EN ISO 8675-2000 Hexagon thin nuts {chamfered} with metric fine pitch thread – Product grades A and B {ISO 8675:1999}
EN 3851-2003 GOOGLEaLL1
EN ISO 4035-2000 Hexagon thin nuts {chamfered} – Product grades A and B {ISO 4035:1999}
EN 4020-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Elbows 90° welded end with thrust wire nut
EN 4011-2003 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy, TI-P100HT {Inconel 718}, silver plated – Classification: 1 550 MPa {at ambient temperature}/600? / Note: To be replaced by EN 4011 {2003-05}.
EN 3064-1996 Aerospace series – Shank nuts, self-locking, serrated – Installation procedure
EN 4445-2000 Aerospace series – Nuts, elliptical clinch, self-locking – Design standard
EN 14218-2003 Hexagon nuts with flange – Fine pitch thread {ISO 10663:1999, modified}
EN 10108-2000 Round steel rod for cold formed nuts and bolts – Dimensions and tolerances
EN 14219-2003 Hexagon bolts with flange with metric fine pitch thread – Small series {ISO 15072:1999, modified}
EN 3230-2001 Aerospace series – Nuts, hexagon, slotted/castellated, reduced height, normal across flats, in steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN ISO 3506-2-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 2: Nuts {ISO 3506-2:1997}
EN 4551-2003 Aerospace series – Pipe coupling 37? in heat resisting steel – Swivel nuts; Inch series
EN 1667-1997 Prevailing torque type all-metal hexagon nuts with flange with metric fine pitch thread {ISO 12126:1997, modified}
EN 4123-2003 Aerospace series – Shank nuts, self-locking, in heat resisting nickel base alloy NI-PH2601 {Inconel 718}, silver plated on thread – Classification: 1 550 MPa {at ambient temperature}/600? / Note: To be replaced by EN 4123 {2003-05}.
EN 782-1992 Hexagon bolts for high-strength structural bolting with large width across flats {short thread length}; product grade C; property class 10.9
EN 493-1992 Fasteners; Surface discontinuities; Nuts
EN 783-1992 Hexagon nuts for structural bolting with large width across flats, style 1; product grade B; property class 10
EN ISO 4759-3-2000 Tolerances for fasteners – Part 3: Plain washers for bolts, screws and nuts – Product grades A and C {ISO 4759-3:2000}
EN ISO 887-2000 Plain washers for metric bolts, screws and nuts for general purposes – General plan {ISO 887:2000}
EN ISO 7040-1997 Prevailing torque type hexagon nuts {with non-metallic insert}, style 1 – Property classes 5, 8 and 10 {ISO 7040:1997}
EN 3065-1996 Aerospace series – Installation holes for self-locking, serrated shank nuts – Design standard
EN 2909-1995 Aerospace series – Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 1100 MPa {at ambient temperature}/650?
EN 4047-2003 Aerospace series – Nuts, self-locking, MJ threads, in heat resisting nickel base alloy, NI-PH2601 {Inconel 718}, silver plated – Classification: 1 550 MPa {at ambient temperature}/600? – Technical specification / Note: To be replaced by EN 4047 {2003
EN 1663-1997 Prevailing torque type hexagon nuts with flange {with non-metallic insert} {ISO 7043:1997, modified}
EN ISO 4032-2000 Hexagon nuts, style 1 – Product grades A and B {ISO 4032:1999}
EN 2881-1998 Aerospace series – Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/120?
EN 4190-2001 Aerospace series – Pipe coupling 8 Degree 30’in titanium alloy – Tees, reduced with thrust wire nut on run
EN ISO 8674-2000 Hexagon nuts, style 2, with metric fine pitch thread – Product grades A and B {ISO 8674:1999}
EN 4018-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Elbows 90°with thrust wire nut
EN 3757-1998 Aerospace series – Nuts, anchor, self-locking, floating, self-aligning, two lug, in heat resisting steel, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/315?
EN 4117-2003 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH2601 {Inconel 718}, silver plated on thread – Classification: 1 550 MPa {at ambient temperature}/600? / Note: To be replaced by EN 4117 {2003-05}.
EN 1662-1997 Hexagon bolts with flange – Small series {ISO/DIS 15071:1996, modified}
EN 3004-1997 Aerospace series – Nuts, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286} – Classification: 1100 MPa {at ambient temperature}/650 ? – Technical specification
EN ISO 4036-2000 Hexagon thin nuts {unchamfered} – Product grade B {ISO 4036:1999}
EN 3720-1995 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425?
EN 3646-006-2001 Aerospace series – Connectors, electrical, circular, bayonet coupling, operating temperature 175? or 200? continuous – Part 006: Receptacle, hermetic, jam-nut mounting; Product standard
EN 3239-1995 Aerospace series – Nuts, bihexagonal, self-locking, in heat-resisting nickel base alloy NI-P101HT {Waspaloy}, silver plated thread – Classification: 1210 MPa {at ambient temperature}/730?
EN 2997-4-1997 Aerospace series – Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 175? continuous, 200? continuous, 260? peak – Part 4: Jam-nut mounted receptacle – Product standard
EN 4444-2000 Aerospace series – Nuts, elliptical clinch, self-locking, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?; Technical specification
EN 2680-1998 Aerospace series – Nuts, anchor, self-locking, floating, self-aligning, two lug, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN 20225-1991 Fasteners; Bolts, screws, studs and nuts; Symbols and designation of dimensions {ISO 225:1983}
EN 4027-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Tees branch with thrust wire nut
EN 3723-1996 Aerospace series – Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425?
EN 3152-2003 Aerospace series – Nuts, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286}, silver plated; Classification: 1100 MPa {at ambient temperature} /425?; Technical specification
EN 2810-2001 Aerospace series – Nuts, hexagon, slotted/castellated, reduced height, normal across flats, in heat resisting steel, passivated – Classification: 900 MPa {at ambient temperature}/650?
EN 3377-1996 Aerospace series – Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT {A286} – Classification: 1100 MPa {at ambient temperature}/425?
EN 4012-2003 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-P100HT {Inconel 718}, MoS2 coated – Classification: 1500 MPa {at ambient temperature}/425? / Note: To be replaced by EN 4012 {2003-05}.
EN 2911-1995 Aerospace series – Shank nuts, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 1100 MPa {at ambient temperature}/650?
EN 4119-2003 Aerospace series – Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT {A286}, silver plated on thread – Classification: 1100 MPa {at ambient temperature}/650? / Note: To be replaced by EN 4119 {2003-05}.
EN 3005-2003 Aerospace series – Nuts, self-locking, in heat resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa/730?; Technical specification / Note: To be replaced by EN 3005 {2003-05}.
EN 4124-2003 Aerospace series – Shank nuts, self-locking, in heat resisting nickel base alloy NI-PH-1302 {Waspaloy}, silver plated on thread, for 60 swage – Classification: 1 210 MPa {at ambient temperature}/730? / Note: To be replaced by EN 4124 {2003-05}.
EN 2907-1995 Aerospace series – Nuts, bihexagonal, self-locking, in heat-resisting steel FE-PA92HT {A286}, silver plated – Classification: 1100 MPa {at ambient temperature}/650?
EN 780-1992 Hexagon nuts for high-strength structural bolting with large width across flats; product grade B; property classes 8 and 10
EN 2879-1998 Aerospace series – Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN ISO 4034-2000 Hexagon nuts – Product grade C {ISO 4034:1999}
EN 2880-1998 Aerospace series – Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/120?
EN 4121-2003 Aerospace series – Shank nuts, serrated, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated on thread – Classification: 1100 MPa {at ambient temperature}/650? / Note: To be replaced by EN 4121 {2003-05}.
EN 3646-004-2001 Aerospace series – Connectors, electrical, circular, bayonet coupling, operating temperature 175? or 200? continuous – Part 004: Receptacle, jam-nut mounting; Product standard
EN 4028-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Tees with thrust wire nut on run
EN 3722-1995 Aerospace series – Shank nuts, self-locking, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425?
EN ISO 10513-1997 Prevailing torque type all-metal hexagon nuts, style 2, with metric fine pitch thread – Property classes 8, 10 and 12 {ISO 10513:1997}
EN 4067-006-2000 Aerospace series – Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260? peak – Part 006: Hermetic jam-nut mounted receptacle – Product standard
EN 14399-3-2002 High-strength structural bolting for preloading – Part 3: System HR; Hexagon bolt and nut assemblies
EN 2753-1996 Aerospace series – Nuts, anchor, self-locking, fixed, single lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/235?
EN 3741-2003 Aerospace series – Nuts, clip, metric – Installation holes and assembly / Note: To be replaced by EN 3741 {2003-05}.
EN 3771-1999 Aerospace series – Nuts, bihexagonal, plain, in heat resisting steel, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 4122-2003 Aerospace series – Shank nuts, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated on thread – Classification: 1100 MPa {at ambient temperature}/650? / Note: To be replaced by EN 4122 {2003-05}.
EN ISO 4033-2000 Hexagon nuts, style 2 – Product grades A and B {ISO 4033:1999}
EN 2647-1995 Aerospace series – Nuts, hexagonal, self-locking, ball seat, in alloy steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN ISO 4759-1-2000 Tolerances for fasteners – Part 1: Bolts, screws, studs and nuts; product grades A, B and C {ISO 4759-1:2000}
EN 4024-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Elbows 45°welded end with thrust wire nut
EN 14399-4-2002 High-strength structural bolting for preloading – Part 4: System HV; Hexagon bolt and nut assemblies
EN 2809-2001 Aerospace series – Nuts, hexagon, slotted/castellated, reduced height, normal across flats, in heat resisting steel, silver plated – Classification: 900 MPa {at ambient temperature}/650?
EN 2910-1994 Aerospace series – Shank nuts, self-locking, in heat resisting steel FE-PA92HT {A286} – Classification: 1100 MPa {at ambient temperature}/650?
EN 4120-2003 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH-1302 {Waspaloy}, sliver plated on thread – Classification: 1 210 MPa {at ambient temperature}/730? / Note: To be replaced by EN 4120 {2003-05}.
EN 2752-1989 Aerospace series; nuts, anchor, self locking fixed, two lug, reduced series, with counterbore; classification: 1100 MPa/235?
EN 4067-004-2000 Aerospace series – Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260? peak – Part 004: Jam-nut mounted receptacle – Product standard
EN 4396-1999 Aerospace series – Shaft-nuts, self-locking, in heat resisting steel FE-PA92HT {A286}, silver plated
EN 3264-2001 Aerospace series – Pipe coupling 8°30′ in titanium alloy – Thrust wire nut
EN ISO 6789-2003 Assembly tools for screws and nuts – Hand torque tools – Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure {ISO 6789:2003}
EN 4013-2003 Aerospace series – Shank nuts, self-locking, in heat resisting nickel base alloy NI-P100HT {Inconel 718}, silver plated – Classification: 1 550 MPa {at ambient temperature}/600? / Note: To be replaced by EN 4013 {2003-05}.
EN 4446-2000 Aerospace series – Nuts, elliptical clinch, self-locking – Installation and removal procedure
EN 4048-2003 Aerospace series – Nuts, self-locking, MJ threads, in heat resisting nickel base alloy NI-PH2601 {Inconel 718}, MoS2 coated – Classification: 1550 MPa {at ambient temperature}/425?; Technical specification / Note: To be replaced by EN 4048 {
EN 4031-2001 Aerospace series – Pipe coupling 8?0 in titanium alloy – Nut for welded ferrule
EN 781-1992 Hexagon bolts for high-strength structural bolting with large width across flats {thread lengths according to ISO 888}; product grade C; property classes 8.8 and 10.9
EN 3721-1995 Aerospace series – Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT {A286}, MoS2 coated – Classification: 1100 MPa {at ambient temperature}/425?
EN 3434-1998 Aerospace series – Nuts, hexagon, slotted/castellated, self-locking, in steel, cadmium plated, MoS2 lubricated – Classification: 900 MPa {at ambient temperature}/235?
EN ISO 7719-1997 Prevailing torque type all-metal hexagon nuts, style 1 – Property classes 5, 8 and 10 {ISO 7719:1997}
EN 28839-1991 Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals {ISO 8839:1986}
EN 1661-1997+AC-1998 Hexagon nuts with flange {ISO/DIS 4161:1996, modified}
EN 3266-2001 Aerospace series – Pipe coupling in titanium alloy – Bulkhead nut
EN 1666-1997 Prevailing torque type hexagon nuts with flange {with non-metallic insert} with metric fine pitch thread {ISO 12125:1997, modified}
EN 2906-1994 Aerospace series – Nuts, bihexagonal, self-locking, in heat resisting steel FE-PA92HT {A286} – Classification: 1100 MPa {at ambient temperature}/650?
EN 3012-1995 Aerospace series – Nuts, bihexagonal, self-locking, in heat-resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa {at ambient temperature}/730?
STANDARDSDESCRIPTION
EN 28839-1991 Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals {ISO 8839:1986}
EN ISO 7085-1999 Mechanical and performance requirements of case hardened and tempered metric thread rolling screws {ISO 7085:1999}
EN ISO 7721-2-1994 Countersunk flat head screws – Part 2: Penetration depth of cross recesses {ISO 7721-2:1990}
EN 22568-1989 Hand- and machine-operated circular screwing dies and hand-operated die stocks {ISO 2568:1988}
EN 4072-1999 Aerospace series – Screws, 100?countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated – Classification: 1100 MPa {at ambient temperature}/425?
EN ISO 6789-2003 Assembly tools for screws and nuts – Hand torque tools – Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure {ISO 6789:2003}
EN ISO 7047-1994 Countersunk raised head screws {common head style} with type H or type Z cross recess – Product grade A {ISO 7047:1994}
EN 4323-2003 Aerospace series – Screws, 100?countersunk head, six lobe recess, threaded to head, in titanium alloy TI-P64001, anodized, MoS2 coated – Classification: 900 MPa {at ambient temperature}/350? / Note: To be replaced by EN 4323 {2003-05}.
EN 2654-1996 Aerospace series – Screws, 100°countersunk normal head, slotted, threaded to head, in brass, tin plated – Classification: 380 MPa {at ambient temperature}/80?
EN 4306-1999 Aerospace series – Sleeves, tubular, for tension screws with flush head, in corrosion resisting steel, passivated, {0,50 mm wall thickness}
EN 2652-1997 Aerospace series – Screws, 100°countersunk normal head, slotted, threaded to head, in alloy steel, cadmium plated – Classification : 900 MPa {at ambient temperature}/235?
EN ISO 4018-2000 Hexagon head screws – Product grade C {ISO 4018:1999}
EN 2928-1996 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718}, silver plated – Classification: 1275 MPa {at ambient temperature}/650?
EN 60998-2-2-2003 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units {IEC 60998-2-2:2002, modified} / Note: Intended as replaceme
EN ISO 14583-2001 Hexalobular socket pan head screws {ISO 14583:2001}
EN ISO 7049-1994 Cross recessed pan head tapping screws {ISO 7049:1983}
EN 27436-1992 Slotted set screws with cup point {ISO 7436:1983}
EN ISO 6410-2-1996 Technical drawings – Screw threads and threaded parts – Part 2: Screw thread inserts {ISO 6410-2:1993}
EN ISO 10666-1999 Drilling screws with tapping screw thread – Mechanical and functional properties {ISO 10666:1999}
EN 4497-1999 Aerospace series – Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 7050-1994 Cross recessed countersunk {flat} head tapping screws {common head style} {ISO 7050:1983}
EN 3306-1996 Aerospace series – Screws, 100°countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 3304-1996 Aerospace series – Screws, 100°countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 10664-1999 Hexalobular internal driving feature for bolts and screws {ISO 10664:1999}
EN ISO 14587-2001 Hexalobular socket raised countersunk {oval} head tapping screws {ISO 14587:2001}
EN 4499-1999 Aerospace series – Screws, 100?countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 27721-1991 Countersunk head screws; Head configuration and gauging {ISO 7721:1983}
EN 320-1993 Fibreboards – Determination of resistance to axial withdrawal of screws
EN ISO 14585-2001 Aerospace series – Nuts, elliptical clinch, self-locking, MJ threads, in heat resisting steel FE-PA2601 {A286}, MoS2 coated – Classification: 900 MPa {at ambient temperature}/425?
EN ISO 1580-1994 Slotted pan head screws – Product grade A {ISO 1580:1994}
EN ISO 4762-1997 Hexagon socket head cap screws {ISO 4762:1997}
EN ISO 10510-1999 Tapping screw and washer assemblies with plain washers {ISO 10510:1999}
EN ISO 3506-3-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 3: Set screws and similar fasteners not under tensile stress {ISO 3506-3:1997}
EN ISO 9173-1-1995 Dental extraction forceps – Part 1: Screw and pin joint types {ISO 9173-1:1991}
EN ISO 14580-2001 GOOGLEaLL1
EN 2926-1996 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 900 MPa {at ambient temperature}/650?
EN ISO 10642-1997 Hexagon socket countersunk head screws {ISO 10642:1997}
EN ISO 2010-1994 Slotted raised countersunk head screws {common head style} – Product grade A {ISO 2010:1994}
EN ISO 10644-1998 Screw and washer assemblies with plain washers – Washer hardness classes 200 HV and 300 HV {ISO 10644:1998}
EN 4509-1999 Aerospace series – Screws, 100?countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 24766-1992 Slotted set screws with flat point {ISO 4766:1983}
EN 3007-1996 Aerospace series – Bolts, hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT {A286}, silv0er plated – Classification: 900 MPa {at ambient temperature}/650?
EN 3305-1996 Aerospace series – Screws, 100°countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
EN 2591-423-2001 Aerospace series – Elements of electrical and optical connection; Test methods – Part 423: Connector rear accessories thread strength / Note: Applies in conjunction with EN 2591-100
EN ISO 1479-1994 Hexagon head tapping screws {ISO 1479:1983}
EN ISO 15483-1999 Cross recessed raised countersunk head drilling screws with tapping screw thread {ISO 15483:1999}
EN ISO 10669-1999 Plain washers for tapping screw and washer assemblies – Normal and large series – Product grade A {ISO 10669:1999}
EN 14399-6-2002 High-strength structural bolting for preloading – Part 6: Plain chamfered washers for systems HR and HV
EN ISO 15481-1999 Cross recessed pan head drilling screws with tapping screw thread {ISO 15481:1999}
EN 2651-1996 Aerospace series – Screws, pan head, slotted, threaded to head, in brass, tin plated – Classification: 380 MPa {at ambient temperature}/80?
EN ISO 2702-1994 Heat-treated steel tapping screws – Mechanical properties {ISO 2702:1992}
EN 3307-1996 Aerospace series – Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN 3308-1996 Aerospace series – Screws, normal hexagonal head, threaded to head, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315 ?
EN ISO 4759-3-2000 Tolerances for fasteners – Part 3: Plain washers for bolts, screws and nuts – Product grades A and C {ISO 4759-3:2000}
EN 4303-1999 Aerospace series – Sleeves, tubular, for tension screws with flush head, in corrosion resisting steel, passivated, {0,25 mm wall thickness}
EN 14399-4-2002 High-strength structural bolting for preloading – Part 4: System HV; Hexagon bolt and nut assemblies
EN ISO 6410-1-1996 Technical drawings – Screw threads and threaded parts – Part 1: General conventions {ISO 6410-1:1993}
EN ISO 7048-1998 Cross recessed cheese head screws {ISO 7048:1998}
EN ISO 3506-1-1997 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 1: Bolts, screws and studs {ISO 3506-1:1997}
EN ISO 14579-2001 Hexalobular socket head cap screws {ISO 14579:2001}
EN ISO 1207-1994 Slotted cheese head screws – Product grade A {ISO 1207:1992}
EN ISO 7046-1-1994 Countersunk flat head screws {common head style} with type H or type Z cross recess – Product grade A – Part 1: Steel of property class 4.8 {ISO 7046-1:1994}
EN 2897-1996 Aerospace series – Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235 ?
EN 26157-1-1991 Fasteners; surface discontinuities; Part 1: Bolts, srews and studs for general requirements {ISO 6157-1:1988}
EN 2937-1994 Aerospace series – Screws, hexagon head, threaded to head, in heat resisting steel FE-PA92HT {A286} – Classification: 900 MPa {at ambient temperature}/650?
EN 2940-1995 Aerospace series – Screws, 100°countersunk head, offset cruciform recess, threaded to head, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 900 MPa {at ambient temperature}/650 ?
EN ISO 3506-4-2003 Mechanical properties of corrosion-resistant stainless-steel fasteners – Part 4: Tapping screws {ISO 3506-4:2003}
EN 3303-1997 Aerospace series – Screws, cap head, hexagon socket, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
EN 2930-1996 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy}, silver plated – Classification: 1210 MPa {at ambient temperature}/730 ?
EN ISO 15480-1999 Hexagon washer head drilling screws with tapping screw thread {ISO 15480:1999}
EN ISO 10673-1998 Plain washers for screw and washer assemblies – Small, normal and large series – Product grade A {ISO 10673:1998}
EN 2939-1994 Aerospace series – Screws, 100°countersunk head, offset cruciform recess, threaded to head, in heat resisting steel FE-PA92HT {A286} – Classification: 900 MPa {at ambient temperature}/650?
EN ISO 898-5-1998 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners not under tensile stresses {ISO 898-5:1998}
EN ISO 2009-1994 Slotted countersunk flat head screws {common head style} – Product grade A {ISO 2009:1994}
EN 20273-1991 Fasteners; Clearance holes for bolts and screws {ISO 273:1979}
EN ISO 4757-1994 Cross recesses for screws {ISO 4757:1983}
EN ISO 14586-2001 Hexalobular socket countersunk head tapping screws {ISO 14586:2001}
EN 60998-2-2-1993 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units {IEC 60998-2-2:1991}
EN 26157-3-1991 Fasteners; surface discontinuities; part 3: bolts, srews and studs for special requirements {ISO 6157-3:1988}
EN ISO 7051-1994 Cross recessed raised countersunk {oval} head tapping screws {ISO 7051:1983}
EN 2929-1996 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT {Waspaloy} – Classification: 1210 MPa {at ambient temperature}/730 ?
EN 2885-1996 Aerospace series – Screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN 2938-1995 Aerospace series – Screws, hexagon head, threaded to head, in heat resisting steel FE-PA92HT {A286}, silver plated – Classification: 900 MPa {at ambient temperature}/650?
EN 2653-1996 Aerospace series – Screws, 100°countersunk normal head, slotted, threaded to head, in corrosion resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/425?
EN ISO 7046-2-1994 Cross recessed countersunk flat head screws {common head style} – Grade A – Part 2: Steel of property class 8.8, stainless steel and non-ferrous metals {ISO 7046-2:1990}
EN 175301-803-1999 Detail specification: Rectangular connectors – Flat contacts, 0,8 mm thickness, locking screw not detachable
EN 60999-2-2003 Connecting devices – Electrical copper conductors; Safety requirements for screw-type and screwless-type clamping units – Part 2: Particular requirements for clamping units for conductors above 35 mm<{hoch}2> up to 300 mm<{hoch}2> {included} {IEC 60999-2
EN ISO 887-2000 Plain washers for metric bolts, screws and nuts for general purposes – General plan {ISO 887:2000}
EN 27435-1992 Slotted set screws with long dog point {ISO 7435:1983}
EN 2884-1996 Aerospace series – Screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 8662-7-1997 Hand-held portable power tools – Measurement of vibrations at the handle – Part 7: Wrenches, screwdrivers and nut runners with impact, impulse or ratchet action {ISO 8662-7:1997}
EN ISO 6410-3-1996 Technical drawings – Screw threads and threaded parts – Part 3: Simplified representation {ISO 6410-3:1993}
EN 3381-1996 Aerospace series – Screws, 100?countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 4017-2000 Hexagon head screws – Product grades A and B {ISO 4017:1999}
EN ISO 7045-1994 Pan head screws with type H or type Z cross recess – Product grade A {ISO 7045:1994}
EN 3543-1997 Aerospace series – Screws, 100°countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/425?
EN 3038-1996 Aerospace series – Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/425?
EN ISO 1483-1994 Slotted raised countersunk {oval} head tapping screws {common head style} {ISO 1483:1983}
EN 2886-1996 Aerospace series – Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN 3035-1996 Aerospace series – Screws, 100°countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated – Classification: 1100 MPa {at ambient temperature}/235?
EN 2927-1996 Aerospace series – Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT {Inconel 718} – Classification: 1275 MPa {at ambient temperature}/650?
EN ISO 14584-2001 Hexalobular socket raised countersunk head screws {ISO 14584:2001}
EN ISO 7380-1997 Hexagon socket button head screws {ISO 7380:1997}
EN 4496-1999 Aerospace series – Screws, 100?countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating – Classification: 1100 MPa {at ambient temperature}/315?
EN 2650-1996 Aerospace series – Screws, pan head, slotted, threaded to head, in corrosion resisting steel, passivated – Classification: 600 MPa {at ambient temperature}/425?
EN ISO 898-1-1999 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs {ISO 898-1:1999}
EN 3759-1996 Aerospace series – Screws, pan head, offset cruciform recess, threaded to head, in heat and corrosion resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/425?
EN 14399-5-2002 High-strength structural bolting for preloading – Part 5: Plain washers for system HR
EN ISO 1481-1994 Slotted pan head tapping screws {ISO 1481:1983}
EN ISO 15482-1999 Cross recessed countersunk head drilling screws with tapping screw thread {ISO 15482:1999}
EN 2649-1995 Aerospace series – Screws, pan head, slotted, threaded to head, in alloy steel, cadmium plated – Classification: 900 MPa {at ambient temperature}/235?
EN 3037-1996 Aerospace series – Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated – Classification: 1100 MPa {at ambient temperature}/315?
EN ISO 8676-2000 Hexagon head screws with metric fine pitch thread – Product grades A and B {ISO 8676:1999}
EN 20898-7-1995 Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm {ISO 898-7:1992}
EN ISO 1478-1999 Tapping screw thread {ISO 1478:1999}
EN 3760-1996 Aerospace series – Screws, 100?countersunk normal head, offset cruciform recess, threaded to head, in heat and corrosion resisting steel, passivated – Classification: 1100 MPa {at ambient temperature}/425?
EN 27434-1992 Slotted set screws with cone point {ISO 7434:1983}
EN ISO 4759-1-2000 Tolerances for fasteners – Part 1: Bolts, screws, studs and nuts; product grades A, B and C {ISO 4759-1:2000}
EN ISO 1482-1994 Slotted countersunk {flat} head tapping screws {common head style} {ISO 1482:1983}
STANDARDSDESCRIPTION
EN 4166-2003 Aerospace series – Clips, spring tension, three parts – PTFE bushes / Note: To be replaced by EN 4166 {2003-05}.
EN 13906-2-2001 Cylindrical helical springs made from round wire and bar – Calculation and design – Part 2: Extension springs
EN ISO 2162-3-1996 Technical product documentation – Springs – Part 3: Vocabulary {ISO 2162-3:1993}
EN ISO 2162-2-1996 Technical product documentation – Springs – Part 2: Presentation of data for cylindrical helical compression springs {ISO 2162-2:1993}
EN 10270-2-2001 Steel wire for mechanical springs – Part 2: Oilhardened and tempered spring steel wire / Note: Applies in conjunction with EN 10021
EN 4168-2003 Aerospace series – Clips, spring tension, three parts – Outer clips in heat resisting steel FE-PA92HT {A286} / Note: To be replaced by EN 4168 {2003-05}.
EN 10092-1-2003 Hot rolled spring steel flat bars – Part 1: Flat bars – Dimensions and tolerances on shape and dimensions
EN 1654-1997+AC-2003 Copper and copper alloys – Strip for springs and connectors
EN 10089-2002 Hot-rolled steels for quenched and tempered springs – Technical delivery conditions
EN 60352-7-2002 Solderless connections – Part 7: Spring clamp connections; General requirements, test methods and practical guidance {IEC 60352-7:2002} / Note: Endorsement notice
EN 4167-2003 Aerospace series – Clips, spring tension, three parts – Inner clips in heat resisting steel FE-PA92HT {A286} / Note: To be replaced by EN 4167 {2003-05}.
EN 10092-2-2003 Hot rolled spring steel flat bars – Part 2: Ribbed and grooved spring leaves; Dimensions and tolerances on shape and dimensions
EN 13906-1-2002 Cylindrical helical springs made from round wire and bar – Calculation and design – Part 1: Compression springs
EN 13906-3-2001 Cylindrical helical springs made from round wire and bar – Calculation and design – Part 3: Torsion springs
EN ISO 2162-1-1996 Technical product documentation – Springs – Part 1: Simplified representation {ISO 2162-1:1993}
EN 13298-2003 Railway applications – Suspension components – Helical suspension springs, steel
EN 61076-2-101-2003 Connectors for electronic equipment – Part 2-101: Circular connectors M8 with screw- or snap-locking, M12 with screw-locking for low voltage applications
EN 14200-2003 Railway application – Suspension components – Parabolic springs, steel
EN 10270-1-2001 Steel wire for mechanical springs – Part 1: Patented cold drawn unalloyed steel wire / Note: Applies in conjunction with EN 10021
EN 13597-2003 Railway applications – Rubber suspension components – Rubber diaphragms for pneumatic suspension springs
EN 10132-4-2000+AC-2002 Cold rolled narrow steel strip for heat treatment – Technical delivery conditions – Part 4: Spring steels and other applications
EN 10151-2002 Stainless steel strip for springs – Technical delivery conditions
EN 10270-3-2001 Steel wire for mechanical springs – Part 3: Stainless spring steel wire / Note: Applies only in conjunction with EN 10021
EN 4590-2000 Aerospace series – Retainers, spring, sheet metal, for self-locking barrel nuts, in corrosion resisting steel, passivated
EN 2591-413-1998 Aerospace series – Elements of electrical and optical connection – Test methods – Part 413: Holding force of grounding spring system
STANDARDSDESCRIPTION
EN 14330-2003 Inland navigation vessels – Studless anchor chain – Round steel link chain
EN ISO 15084-2003 Small craft – Anchoring mooring and towing – Strong points {ISO 15084:2003}
EN 353-1-2002 Personal protective equipment against falls from a height – Part 1: Guided type fall arresters including a rigid anchore line